Switch

SW-MG2154F

48port GE + 6port  SFP+

  • 48*RJ45 ports + 6 SFP+ ports
  • Web UI for configuration
  • Console port with CLI command
  • HW monitor Alarm
  • Fanx3
  • Internal power supply
  • Operating: 0 ~ 50℃
  • Dimension: 441(W) x 270(D) x 45(H) mm
GE+10GE

SW-MG2154F is the advanced fanx3 GbE Managed Switch supports  48xGbE Ethernet ports ; specifically designed for connecting to IP Camera, WiFi Access Point …devices. 
 

Powerful  6 x 10Gb SFP+ Uplink

48GbE ports for high-speed connections and up to 60 Gbps of fiber-optic uplinking capability allowing the SW-MG2156FP to be easily deployed in multiple physical locations, such as branches, retails, or remote workgroup environment for larger network access.
 

Scenarios

L2 Managed, as a middle-layer or lower-layer architecture, connects devices such as lower-layer PoE AP/IP cam.
SW-MG2154FP with 48 ports,There is also a 24-port SW-MG2128FP for matching.


Hardware
Controller
Realtek RTL9311+RTL8218D
Memory
Flash 32MB/DDR 2Gb
Interface
48x GbE ports, RJ45
6 x 10G ports, SFP+
Reset Button: reset to default setting, re-start system
Console port by RJ45 type
LED Indicator
PWR: Green LED 
    Off: power off or fail
    On: power on
SYS: Green LED
    Off: power off or fail
    On: system is ready
    Blinking: system booting up
Alert: Red LED
    Off: Switch is normal condition
    On: Alarm for system failure because of overheat, wrong voltage.
1-48 Port LED:
 Link/ACT:
    Off: port disconnected or link fail
    Green on: 1000Mbps connected
    Amber on: 10/100Mbps connected
    Blinking: sending or receiving data
49-54 port LED:
 SFP+: 
         - Off: disconnected or fail
         - Blue: 10Gbps connected
         - Green: 1000Mbps connected
         - Blinking: data transmitting
HW Feature
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3ab 1000BASE-T
IEEE802.3ae SFP+
IEEE802.3az EEE
MAC address Table: 32K
Packet buffer size: 16Mbit
Jumbo Frame: 12K bytes
216Gbps switching capacity
Forwarding rate: 129.3Mpps (64-byte package size)
System Monitor
HW Monitor IC: ADT7463
    Voltage Monitor
    Input Voltage : 12V (+/-7% Alarm Threshold)
    I/O Voltage : 3.3V (+/- 5% Alarm Threshold)
    DDR Voltage : 1.5V (+/- 5% Alarm Threshold)
    PHY Voltage : 1.1V (+/- 5% Alarm Threshold)
    MAC Voltage:1.0V (+/- 5% Alarm Threshold)
    Temperature Monitor
    BOARD: 0~80C
    MAC: 0~85C
    PHY: 0~85C
Power
Internal power supply
Input: 90~264VAC/47~63Hz
Output: 12V/6A
Reset Button
Support reset to default configuration
Install
Rackmount
Housing 
Metal
Dimension
441(W) x 270(D) x 45(H) mm
Temperature
Operating: 0 ~ 50℃
Storage : -40 ~ 70℃
Humidity
Operating: 10% ~ 90% RH (non-condensing)
Storage: 5% ~ 90% RH (non-condensing)
Software
Status
System Information
Logging Message
Port Statistics/Error Disabled/Bandwidth Utilization
Link Aggregation Group/Port Setting/LACP
Port
IP Address
System Time
PoE
Global Setting/Priority Setting/Power Limit/Power Show
VLAN
Voice VLAN/Protocol VLAN/MAC VLAN/Surveillance VLAN/GVRP
MAC Address Table
Dynamic Address/Static Address/Filtering Address
Spanning Tree
Property/Port Setting/MST Instance/MST Port Setting/Statistics
Discovery
LLDP
Multicast
Group Address/Router Port/Forward All Table/
Throttling/Filtering Profile/Filtering Binding/IGMP Snooping/MLD Snooping/MVR
Security
RADIUS/RADIUS/AAA/Management Access/Authentication Manager
Port Security/Protected Port/Storm Control/DoS/Dynamic ARP Inspection
Dynamic ARP Inspection/IP Source Guard
ACL
MAC ACL/MAC ACE/IPv4 ACL/IPv4 ACE/IPv6 ACL/IPv6 ACE/ACL Binding
QoS
CoS / DSCP / CoS-DSCP / IP Precedence/Rate Limit
Diagnostics
Logging /Mirroring/Ping/Traceroute/Copper Test/Fiber Module/UDL
Management
User Account/Firmware/Configuration/SNMP/RMON